Search found 1100 matches

by thinwater
Fri Apr 09, 2021 8:51 pm
Forum: PDQ Altair (PDQ 32) Forum
Topic: Shift and Throttle cable replacement
Replies: 3
Views: 343

Re: Shift and Throttle cable replacement

Get coupling nuts, so that you can use the old cables to pull the new cables through. If you can't find them, PM. I've got a bag of them, I think.
by thinwater
Wed Mar 31, 2021 5:58 pm
Forum: PDQ Capella (PDQ 36) Forum
Topic: Bottom of keel photo and question
Replies: 7
Views: 1762

Re: Bottom of keel photo and question

SJM: You may not have understood James. When he suggested finding out if the keels were flooded, he did NOT mean whether they was water in the bilge, he meant "did water drain out of the keel when hauled" or did you drill a hole to find out. Because they are separate you would NOT find water in the ...
by thinwater
Tue Dec 15, 2020 4:41 pm
Forum: PDQ General Forum
Topic: Dingy motor hoist
Replies: 7
Views: 4486

Re: Dingy motor hoist

The OP asked for something that could clamp on the rail. That is almost certain to either bend the rail or start a leak at the stanchion base. Not a good idea.
by thinwater
Tue Oct 06, 2020 1:40 pm
Forum: PDQ Powercat Forum
Topic: Bottom Paint
Replies: 2
Views: 1104

Re: Bottom Paint

I have a bit of a problem with Seahawk. They have probably changed their ways, but for years they were producing top performing paints by illegally blending tin in with the copper. This went on for 5 years and resulted in jail time and big fines. It was not an accident or oversight, it was intention...
by thinwater
Sat Aug 22, 2020 10:50 am
Forum: PDQ Capella (PDQ 36) Forum
Topic: Vented loop re direct discharge
Replies: 1
Views: 888

Re: Vented loop re direct discharge

It hinges upon whether the bowl lip and top of the holding tank are above the waterline. I believe they both are (were on my PDQ 32), so no vented loops. Monohulls are different. That said, you may want to loop the hose just above the water line to reduce flow-back in the the bowl. The pump will mos...
by thinwater
Sun Aug 09, 2020 6:04 pm
Forum: PDQ Powercat Forum
Topic: Anchor Bridle
Replies: 10
Views: 2870

Re: Anchor Bridle

Calculating the strnegth of the cleats is a matter of looking at the fixing boats and the backing plates. On the PDQs I've seen, the rope would probably break first, or at least not last long. They are stronger than anchoring loads require. As for the bending force on the bows, it is really quite sm...
by thinwater
Sat Aug 01, 2020 1:52 pm
Forum: PDQ Capella (PDQ 36) Forum
Topic: Can 2019/2020 manual tilt Yamaha 9.9s be used on a PDQ 36?
Replies: 2
Views: 1670

Re: Can 2019/2020 manual tilt Yamaha 9.9s be used on a PDQ 36?

Try Andy Jr. at Shipyard Island Marina (800-213-3323). Many PDQ owners have gotten motors from him. He will adapt the handles and wiring harness so that it is a drop-in fit. http://sail-delmarva.blogspot.com/2012/08/new-engines.html This is the procedure. http://sail-delmarva.blogspot.com/2009/11/re...
by thinwater
Sun Jul 05, 2020 5:21 pm
Forum: Classifieds
Topic: 2001 PDQ 32 For Sale Newburyport, MA
Replies: 3
Views: 1947

Re: 2001 PDQ 32 For Sale Newburyport, MA

I think it will really help your cause if you post pictures and probably create a blog or similar.

Good luck!
by thinwater
Tue May 19, 2020 7:00 pm
Forum: PDQ Altair (PDQ 32) Forum
Topic: What Dinghy
Replies: 5
Views: 2487

Re: What Dinghy

The PO glued the lifting eyes on (Defender Marine caries them). I added the holes in the wood floor. Also, the original spreader bar was plastic, and it failed while under spinnaker! Because I was single handing and it would have taken critical minutes to get the chute in and stop the boat, I just a...
by thinwater
Sun May 17, 2020 7:50 pm
Forum: PDQ Altair (PDQ 32) Forum
Topic: What Dinghy
Replies: 5
Views: 2487

Re: What Dinghy

A short strap on the transom and a spreader bar up front. I could get the dingy tight against the bars. With a soft floor, proper inflation and tricing under the dinghy (cris-cross lines) once it is up will be vital. (Although I now sail a Corsair F-24, I owned a PDQ 32 for many years and there is a...
by thinwater
Tue Apr 28, 2020 3:57 pm
Forum: PDQ Powercat Forum
Topic: Microwave Addition
Replies: 6
Views: 3466

Re: Microwave Addition

The most common problem with running a microwave off an inverter is that the power is too noisy. It needs to be a pure sine wave inverter, not modified sine wave. Short of replacing the inverter, there is no easy solution. Asa result, the microwave probably ran fine on shore power, but not from the ...
by thinwater
Wed Apr 08, 2020 12:20 pm
Forum: PDQ Altair (PDQ 32) Forum
Topic: Charging from Portable Generator
Replies: 11
Views: 4223

Re: Charging from Portable Generator

You don't need to disassembly the boom to fix the reefing lines. The blocks put a twist in them and as a result, they wind up in the middle. You can untwist the lines working with a flashlight from the boom end (because that is where 6the twist came from). This needs to be done every few years if yo...
by thinwater
Tue Apr 07, 2020 1:43 am
Forum: PDQ General Forum
Topic: Storage
Replies: 6
Views: 3686

Re: Storage

You might want to investigate insurance. Many have a BIG jump south of the VA/NC border due to huricane risk.
by thinwater
Fri Mar 13, 2020 12:08 am
Forum: PDQ Powercat Forum
Topic: Water in Fuel Sensor
Replies: 7
Views: 4027

Re: Water in Fuel Sensor

I'm guessing re. the PDQ installation, but... * The sensor is nothing more than a pair of copper stubs that allow conductivity (no float). There is little that can go wrong, other than get dirty. A wet connection can cause a false positive, as can a chafed wire. Could be a poor connection that fails...