PDQ OWNERS FORUM

Hi Josh ! Here are photos. You can see the amount of light that was added, and the ventilation is great. A heads up if ordering from West Marine - one of the hatches that they sent had been previously installed by someone else and returned to the store. There was some cosmetic damage. I should have ...

John, you are hot on the trail again ! It was impeller related. My pump set up is a little different than yours. As it turns out, there is a "bleed hose" that connects the waste body to the seawater body, which explains the waste cross-over to the seawater. If I had looked at the exploded ...

I recently found myself in significant back pain, courtesy of some repairs to Easy Riders combined with my own recklessness. Fortunately, Dick Tuschick loaned me his book "7 Steps to a Pain Free Life". The book has a bunch of information, including some simple exercises that help ease pain...

Thanks John ! I'll report back on the results.

Easy Riders (Hull #29) has what may be the original Jabsco head, but I can't see any nameplate info. Saltwater flush. A prior owner converted the manual pump to the Jabsco 29200-0120 electric toilet conversion pump in the photo. This is a little graphic, so don't read further if you're eating ... Wh...

Credit for this goes to Brian on Clementine, who saw this thread, and went with Corinthian Aquamat with the teak floor look, for interior flooring. Brian gave me the details on what he did. Easy Riders has fiberglass flooring in the lower salon. It was hard to keep clean - little bits of dirt would ...

Here's some info on parts for adding deck hatches above the shower and galley (for those of us who don't have them). I'm using Bowmar N-1000-10A hatches with a 10-3/4 x 10-3/4 cutout. Found them at West Marine (online). The trim ring part number is NT-2000-OFF-W for the 1-inch trim ring, off white. ...

On Hull #29, in the cabinet under the refrigerator, there is a wood floorboard that you lift to access the bilge below, which has the sea cocks for the raw water intake for the salon air conditioner and genset. I was not being diligent in inspecting this area, since I had to first haul all the galle...

On adding a cabinet to the dead space to the port side of the Liquor Cabinet: The Legendary Hull #29 has stepped forward once again to be the guinea pig, under the precise operational and engineering management of the esteemed and talented James Power. We're doing this in two stages: Stage 1: Cut an...

I gave the PSS Pro's a good beating during a rough crossing from Key Biscayne to Bimini. They performed great !

I installed the Bouge in January, and it has worked great. I ran a separate 12v circuit up to the flybridge with 12 ga wire. If the voltage indicator on the Bouge is correct, I'm getting a voltage drop of 0.5 to 0.75. So I would recommend using 10 ga wire. I compensated by setting the low voltage cu...

Hi BJ - Replacing this hose was my first job on Easy Riders. The old hose had adhered itself to the bottom of the shower pan. I softened it up a little with a 350 watt heat gun. My Hull #29 configuration may be different than yours. Give yourself plenty of length on the new hose, so it does not kink...

For single handing thru the locks on the Okeechobee Waterway - Check the Okeechobee Waterway website and Notice to Mariners several times before your trip to confirm all locks are open. Put on your life jacket before entering the lock. I put out all my fenders port and starboard, being sure to get o...

Over the summer, I removed my Princess Cooktop and replaced it with an electric induction cooktop. I was motivated by Harold and Trish on Hull #5, who said "it was really easy to do". (Note that Easy Riders is the classic MV 34 model, and some information may not apply to the PDQ Yacht mod...

To add to the above - Easy Riders' plumbing system is the Whale 15mm with push fittings. I had an assortment of fittings but did not have spare shut off valves to use in case of a leak. One of the cockpit shower flex hoses ruptured, and I had to shut down the water system. An easy fix would have bee...