Installing PUR 40e watermaker
Posted: Mon Apr 26, 2004 6:12 am
Cruising
Posted by Keith and Charlotte Katmantoo AKA Samtosha on January 29, 2003 at
16:52:00:
Hi:[/i]
My wife and I purchased "Samtosha", PDQ 32 in Annapolis, MD in November and
frantically began outfitting her (now Katmantoo) for a trip to the Bahamas. We
managed to throw the dock lines off after 2 weeks and plowed through ice on the
creek to head south
We are now in St. Augustine, FL getting some new bottom paint and enjoying the
warm weather. We have installed a wind generator which manages to keep up with
the refrigeration needs. We have a PUR 40e watermaker waiting for installation
I haven't gotten around to it yet. Anybody have recommendations for location
without adding a new through-hull? I planned to tee into the head intake. Unit
supposed to be installed below the waterline. Any suggestions will be greatly
appreciated
Cheers,
Keith and Charlotte
S/V Katmantoo
Follow Ups:
Re: Cruising Colin Swithenbank 09:16:22 02/01/03 (0)
--------
Re: Cruising
Posted by Colin Swithenbank on February 01, 2003 at 09:16:00:
In Reply to: Cruising posted by Keith and Charlotte Katmantoo AKA Samtosha on
January 29, 2003 at 16:52:00:
Keith and Charlotte: Congratulations on your PDQ: you've made a great choice
Our PUR watermaker was factory installed under the settee opposite the nav
station and plumbed into the head intake as you suggest. This puts the unit
below the waterline. Be careful to keep the feed hose as low as possible: mine
loops briefly up above the waterline and I get airlocks which need an auxiliary
manual water pump to clear. The feed to the head can loop above the waterline
and may actually help clear airlocks
The waste flow from my unit is plumbed through a throughhull just above the
waterline right above the unit. You may be able to plumb this line back to the
sink drain if you want to avoid a new throughull, but I haven't had any problem
with mine
Colin
Posted by Keith and Charlotte Katmantoo AKA Samtosha on January 29, 2003 at
16:52:00:
Hi:[/i]
My wife and I purchased "Samtosha", PDQ 32 in Annapolis, MD in November and
frantically began outfitting her (now Katmantoo) for a trip to the Bahamas. We
managed to throw the dock lines off after 2 weeks and plowed through ice on the
creek to head south
We are now in St. Augustine, FL getting some new bottom paint and enjoying the
warm weather. We have installed a wind generator which manages to keep up with
the refrigeration needs. We have a PUR 40e watermaker waiting for installation
I haven't gotten around to it yet. Anybody have recommendations for location
without adding a new through-hull? I planned to tee into the head intake. Unit
supposed to be installed below the waterline. Any suggestions will be greatly
appreciated
Cheers,
Keith and Charlotte
S/V Katmantoo
Follow Ups:
Re: Cruising Colin Swithenbank 09:16:22 02/01/03 (0)
--------
Re: Cruising
Posted by Colin Swithenbank on February 01, 2003 at 09:16:00:
In Reply to: Cruising posted by Keith and Charlotte Katmantoo AKA Samtosha on
January 29, 2003 at 16:52:00:
Keith and Charlotte: Congratulations on your PDQ: you've made a great choice
Our PUR watermaker was factory installed under the settee opposite the nav
station and plumbed into the head intake as you suggest. This puts the unit
below the waterline. Be careful to keep the feed hose as low as possible: mine
loops briefly up above the waterline and I get airlocks which need an auxiliary
manual water pump to clear. The feed to the head can loop above the waterline
and may actually help clear airlocks
The waste flow from my unit is plumbed through a throughhull just above the
waterline right above the unit. You may be able to plumb this line back to the
sink drain if you want to avoid a new throughull, but I haven't had any problem
with mine
Colin